EXTERIOR TRIM

CAR IDENTIFICATION JENSEN HEALEY

VIN-Numbers and Year

VIN	YEAR
Prototypes	1974
1000-1299	1974
1300-1399	1974-75
1400-1799	1975
1800-1899	1975-76
1900-1999	1976
9400-9999	1974

Year and Models

Year	Model
1935-36	The White Lady
1936-45	S-Type
1938-46	H-Type
1946-52	PW
1950-58	(Early) Interceptor 4 litre
1954-64	541
1962-66	C - V8
1964-66	P66
1966-71	FF
1966-76	Interceptor
1971-73	Inerceptor SP
1972-76	Jensen-Healey
1983-92	Interceptor S4
2000-05	S - V8

The Jensen Healey and Jensen GT were built by Jensen Motors Ltd. of West Bromwich, England from March 1972 until May 1976. A little over 10,000 convertibles were manufactured during this time. Some of the last Jensens to roll out the doors were the Jensen GT ('76 model year) of which a scant 509 were produced. All Jensen Healey and Jensen GT automobiles came equipped with the brand-new 2 litre, 16-valve Lotus built 907 engine. Home market and European destination cars had twin 40mm Dellorto carburetors while U.S. Federal destination cars came with twin Stromberg carburetors. Jensen Motors numbered the JH starting at 10000 in 1972. 10000-13349 are Mark I cars. 13500-20504 are Mark II cars. 18900 + VINs also have the JH-5s mixed in. Jensen GT numbers started at 30000 in September '75.

Jensen Healey, 1972 - 1973 (Mk l) March 1972 - May 1973 VIN 10000-13349
The Jensen Healey debuts in March '72. Original cars have a simple but pleasant interior; plastic center console, no wood on dash board (72 only) or wood on glove box, rubber floor mats, black interiors (a few early cars are seen with tan interior) and square-cornered headlight cowls distinguish these models. Very early cars will have the noteable absence of a passenger side door lock (quickly added on the '73 model year) and auxillary oil filler canister mounted to firewall in engine compartment. Some early cars have no oil cooler as well.

Numbers manufactured - 3,356

Jensen Healey, 1974 - 1975 (Mk II) August 1973 - August 1975 VIN 13500-20504
In 1974 performance and mechanical specification remain the same but the trim level is upgraded throughout; wood facia is added to the dash, padded center console, floor carpeting & additional bright work details added to exterior. Round cornered headlight cowl with one piece front wings most notable "Mark II" feature. High quality, double . skinned, factory hard top and dealer installed A/C introduced. Steel rear bumpers stand off body a few extra inches compared to earlier models- in preparation for the soon to come impact bumpers seen in "74 1/2" cars as well as 5-speed transmission. '74 at left has steel bumpers and aftermarket Panasport wheels.

Numbers manufactured - 7,142 (includeds all JH5s mentioned below)

Jensen Healey - JH5 December 1974 - August 1975 approx. VIN 18,900-20504 (concurrent with non-JH5 MKII)
The JH5 Mystery - Many (but not all) 1975 roadster models see the JH5 badging on the side. These cars have impact bumpers and 5-speed Getrag transmission. Most obvious change is special combination JH-5/Union Jack badge in place of J-badge on front wings. Numerous small details under the hood include viscous fan clutch on radiator fan, new upper radiator $hose intake from water pump to radiator arrangement, catalytic converter and additional "improved" exhaust emmission package. There is no offical VIN or month cut off for the JH5, earliest sightings are commission dates of Dec. '74. Factory build cards offer no clue to when or why JH5 models exist.

Numbers manufactured - unknown

Jensen GT, 1976 VIN 30000-30510 September 1975 - May 1976
Jensen goes "up market" with GT hardtop. Donald Healey departs Jensen Motors, hence dropping of "Healey" moniker. Jensen GT has revamped badges to reflect this. Smooth, quiet, refined? the GT offers luxuriously appointed full, burl wood dash and factory installed air conditioning for all U.S. bound models (all Jensen Healeys with A/C were dealer installed). Sticker price in U.S. crests well over $11,000, astonishing the motoring public at that time. New Look paisley interior seat surfaces seen in a few cars are unforgetable. GT is rushed into production (resulting intensive labor costs burden the already overtaxed company) and even though Interceptor models shore up sales, time is running out for Jensen Motors. Wildcat strikes, continual parts shortages, inflation, a shakey financial footing, and bad economic conditions all contribute to closing the doors of Jensen Motors in May, 1976.

Numbers manufactured - 509

Quelle jensencars.be / jensenhealey.com

Ill.no.	Partno.	Part	Quantity required	Info	Price
1	91013	FINISHER BOOT LID	1		CHF 356.31

Ill.no.	Partno.	Part	Quantity required	Info	Price
3	91940	STUDE PLATE-FINISHER TO WING	2		CHF 3.50

Ill.no.	Partno.	Part	Quantity required	Info	Price
4	65501	WASHER PLAIN	6 / 2	6 needed up to chassis 13349, chassis 13350 on, just 2	CHF 1.80

Ill.no.	Partno.	Part	Quantity required	Info	Price
5	65315	NUT	6 / 2	6 needed up to chassis 13349, chassis 13350 on, just 2	CHF 1.60

Ill.no.	Partno.	Part	Quantity required	Info	Price
6	92148	USE 91940	3

Ill.no.	Partno.	Part	Quantity required	Info	Price

Ill.no.	Partno.	Part	Quantity required	Info	Price
8	66820	CLIP MOULDING	7		CHF 3.00

Ill.no.	Partno.	Part	Quantity required	Info	Price
9	91014	FINISHER - REAR WING L.H.	1		availability request

Ill.no.	Partno.	Part	Quantity required	Info	Price
12	91940	STUDE PLATE-FINISHER TO WING	4		CHF 3.50

Ill.no.	Partno.	Part	Quantity required	Info	Price
13	65501	WASHER PLAIN	4		CHF 1.80

Ill.no.	Partno.	Part	Quantity required	Info	Price
14	65315	NUT	4		CHF 1.60

Ill.no.	Partno.	Part	Quantity required	Info	Price
18	90768	FINISHER DOOR STEP MKII	1		availability request
18	90769	FINISHER DOOR STEP	1		availability request

Ill.no.	Partno.	Part	Quantity required	Info	Price
20	98331	GASKET FRONT WING MOTIF	1	Gasket not as illustrated - fits to the Plate	availability request
20	98314	BASE PLATE FRONT WING MOTIF JH-5	1	without sticker - not as illustrated	availability request
20	98317	MOTIF J.H.5	1	Motif not as illustrated	CHF 10.54

Ill.no.	Partno.	Part	Quantity required	Info	Price
21	67160	BUSH PLASTIC	4	Up to Chassis 13349	CHF 1.50

Ill.no.	Partno.	Part	Quantity required	Info	Price
22	92581	FINISHER B-POST	1	From Chassis 13350	availability request

Ill.no.	Partno.	Part	Quantity required	Info	Price
24	91602	BADGE - BONNET	1		CHF 194.25

Ill.no.	Partno.	Part	Quantity required	Info	Price
25	66830	BUSH PLASTIC	2		CHF 1.05

Ill.no.	Partno.	Part	Quantity required	Info	Price
26	97057	MOUDING-FRONT WING-SHORT	1	USA - From Chassis 13350	availability request

Ill.no.	Partno.	Part	Quantity required	Info	Price
27	97064	MOULDING SHORT FRONT WING	2		CHF 19.41

Ill.no.	Partno.	Part	Quantity required	Info	Price
28	97065	MOULDING FRONT WING LONG LH	1	Europe - LHD, Europe - RHD / From Chassis 13350	availability request
28	97066	MOULDING FRONT WING LONG RH	1	Europe - LHD, Europe - RHD / From Chassis 13350	availability request

Ill.no.	Partno.	Part	Quantity required	Info	Price
30	97060	MOULDING-DOOR-SHORT	2	Europe - LHD, Europe - RHD / From Chassis 13350	CHF 3.90

Ill.no.	Partno.	Part	Quantity required	Info	Price
32	97068	FINISHER DOOR TOP OUTER	2	Europe - LHD, Europe - RHD / From Chassis 13350	CHF 59.24

Ill.no.	Partno.	Part	Quantity required	Info	Price
33	97073	T STUD FASTENER	10		CHF 1.80

Ill.no.	Partno.	Part	Quantity required	Info	Price
34	97073	T STUD FASTENER	2		CHF 1.80

Ill.no.	Partno.	Part	Quantity required	Info	Price
35	67162	BUSH PLASTIC	2		CHF 1.50

Ill.no.	Partno.	Part	Quantity required	Info	Price
1	91013	FINISHER BOOT LID	1		CHF 356.31
3	91940	STUDE PLATE-FINISHER TO WING	2		CHF 3.50
4	65501	WASHER PLAIN	6 / 2	6 needed up to chassis 13349, chassis 13350 on, just 2	CHF 1.80
5	65315	NUT	6 / 2	6 needed up to chassis 13349, chassis 13350 on, just 2	CHF 1.60
6	92148	USE 91940	3
8	66820	CLIP MOULDING	7		CHF 3.00
9	91014	FINISHER - REAR WING L.H.	1		availability request
12	91940	STUDE PLATE-FINISHER TO WING	4		CHF 3.50
13	65501	WASHER PLAIN	4		CHF 1.80
14	65315	NUT	4		CHF 1.60
18	90768	FINISHER DOOR STEP MKII	1		availability request
18	90769	FINISHER DOOR STEP	1		availability request
20	98331	GASKET FRONT WING MOTIF	1	Gasket not as illustrated - fits to the Plate	availability request
20	98314	BASE PLATE FRONT WING MOTIF JH-5	1	without sticker - not as illustrated	availability request
20	98317	MOTIF J.H.5	1	Motif not as illustrated	CHF 10.54
21	67160	BUSH PLASTIC	4	Up to Chassis 13349	CHF 1.50
22	92581	FINISHER B-POST	1	From Chassis 13350	availability request
24	91602	BADGE - BONNET	1		CHF 194.25
25	66830	BUSH PLASTIC	2		CHF 1.05
26	97057	MOUDING-FRONT WING-SHORT	1	USA - From Chassis 13350	availability request
27	97064	MOULDING SHORT FRONT WING	2		CHF 19.41
28	97065	MOULDING FRONT WING LONG LH	1	Europe - LHD, Europe - RHD / From Chassis 13350	availability request
28	97066	MOULDING FRONT WING LONG RH	1	Europe - LHD, Europe - RHD / From Chassis 13350	availability request
30	97060	MOULDING-DOOR-SHORT	2	Europe - LHD, Europe - RHD / From Chassis 13350	CHF 3.90
32	97068	FINISHER DOOR TOP OUTER	2	Europe - LHD, Europe - RHD / From Chassis 13350	CHF 59.24
33	97073	T STUD FASTENER	10		CHF 1.80
34	97073	T STUD FASTENER	2		CHF 1.80
35	67162	BUSH PLASTIC	2		CHF 1.50