REAR AXLE

CAR IDENTIFICATION MG A

Year	Model	Numbers manufactured
September 1955 to May 1959	MGA 1500cc	10101 to 68,850
September 1958 to June 1960	MGA Twin Cam	501 to 2611
May 1959 to April 1961	MGA 1600cc	68,851 to 100,351
April 1961 to June 1962	MGA 1600cc MkII	100,352 to 109,070

BMC 'B' Series Engine Use(1953 to 1981)

Model	cc	Prefix	BHP/RPM	Torque
M.G. MGA	1489	BP15GB,15GB	68/5200	82
M.G. MGA	1489	15GD	72/5500	85
M.G. MGA 1600	1588	16GA	80/5600	87
MGA Twin Cam	1588	BC16GB	108/6700
M.G. MGA 1600 Mk2	1622	16GC	90/5500 97

MGA Serial Numbers

Engine Number

The engine number is stamped on a plate secured to the righthand side of the cylinder block...or it is stamped on a plate secured to the rear of the engine behind the cylinder block. (Twin Cam)

Car Number

The car number is stamped on a plate secured to the top lefthand side of the dash panel

Gearbox Number

The gearbox number is stamped on the top of the gearbox casing adjacent to the dipstick

Body Number

The body number is stamped on a plate secured to the bulkhead between the righthand bonnet hinge and the fuse block.

Rear Axle Number

The rear axle No is stamped on the front of the axle tube on the LH side next to the spring seat.

Identifying the MGA

There are only five variations of the MGA. The 1500cc, 1600cc, MkII, Twin Cam and 1600cc MkII De luxe. The Coupés were a variation of the Roadster and were not differentiated by the factory numbering system as to body style. The Twin Cam, a major undertaking at the time of its introduction, was identified separately while the De luxe, the most elusive of MGA models, was not distinctly identified. There are reliable production figures for all models except the De luxe.

The three major MGA models may be readily identified by their tail-lamp and grille configurations as well as their engine displacement.

A 1500cc will have the familiar single Lucas tail lamp, the flush style grille and no shroud or boot lid emblems. Four-wheel drum brakes were fitted to this model only.

Very early 1500ccs had different style gauge faces, an example of which can be found in the factory service manual and drivers handbook illustrations. The door rails on the first few cars were entirely of wood as were the cockpit rear corners. There are few of these seen today. The 1500's did not have the starter hump on the passenger toe board or the windscreen mounted hood clamp. The turn indicators were switched through a relay.

1600cc is differentiated by the dual rear lamp with separate turn lamps, larger round parking lamps with flat lenses and a '1600cc' marker on the cowl and rear boot lid. Disc brakes on the front greatly improved stopping power. The starter position was moved with the resulting hump on the passenger toe board.

The 1600cc MkII received the closest thing to a face lift an MGA ever got. The famous flat grille was replaced with the 'pre-crushed' version. The MkI Mini rear lamps appeared horizontally below the boot lid and the vinyl covered dash and cowl and 1600cc MkII badges were added. The chrome trim and dash escutcheon from the Coupé finished off the dash. Seat belt anchors were added to the chassis. 1600cc MkII De luxe cars used the Twin Cam chassis with the push rod 1622cc engine. Check all parts carefully, as MGA's have not always enjoyed the respect they do now, and parts have been freely exchanged with little regard for originality. When re-wiring your car, be sure to order the loom that fits your body type, not engine type.

Ill.no.	Partno.	Part	Quantity required	Info	Price
1	1G7582	HUB LOCKING NUT LH THREAD	1		CHF 41.35
1	1G7448	LOCKING NUT RH	1/2		CHF 41.35

Ill.no.	Partno.	Part	Quantity required	Info	Price
2	1G7584	WASHER, LOCKING	2		CHF 6.90

Ill.no.	Partno.	Part	Quantity required	Info	Price
3	6K499	DRAIN PLUG	2		CHF 4.95

Ill.no.	Partno.	Part	Quantity required	Info	Price
4	21H6060	VALVE, BREATHER REAR AXLE CASING	1		CHF 14.00

Ill.no.	Partno.	Part	Quantity required	Info	Price
5	1G7465	GASKET, DIFFERENTIAL	1		CHF 2.05

Ill.no.	Partno.	Part	Quantity required	Info	Price
6	BTB328	DIFF CAGE BANJO AXLE	1		availability request (add quantity to basket, offer follows)

Ill.no.	Partno.	Part	Quantity required	Info	Price
8	CHM163	BEARING DIFFERENTIAL CARRIER	2		CHF 41.80

Ill.no.	Partno.	Part	Quantity required	Price
9	2K7993	SHIM BEARING PACKING 0.002"	a/r	CHF 5.75
9	ATB7239	SHIM B/AXLE .003	a/r	CHF 5.00
9	2K7435	SHIM BEARING PACKING, 0.004"	a/r	CHF 5.90
9	6K503	SHIM B/AXLE .006	a/r	CHF 6.10

Ill.no.	Partno.	Part	Quantity required	Info	Price
10	ATB7122	DIFF GEAR MGA1500	2	1500cc	CHF 192.85
10	ATB7282	DIF GEAR NCA	2	1600cc To (c)82892 s/wheel To (c)82748 wire wheel	availability request (add quantity to basket, offer follows)
10	BTB150	DIFFERENTIAL WHEEL 25 SPLINE	2	1600cc From (c)82893 s/wheel From (c)82749 wire wheel	CHF 182.30

Ill.no.	Partno.	Part	Quantity required	Info	Price
11	ATB7072	THRUST 35THOU STD	2		CHF 8.45

Ill.no.	Partno.	Part	Quantity required	Info	Price
12	ATB7123	PLANET GEAR MGB	2		CHF 135.80

Ill.no.	Partno.	Part	Quantity required	Info	Price
13	1G7445	THRUST WASHER, PINION	2		CHF 10.10

Ill.no.	Partno.	Part	Quantity required	Info	Price
14	1G7444	SHAFT, PINION GEAR	1		CHF 62.55

Ill.no.	Partno.	Part	Quantity required	Info	Price
15	6K842	DIFF PEG NCA	1		availability request (add quantity to basket, offer follows)

Ill.no.	Partno.	Part	Quantity required	Info	Price
16	ATA7043	BOLT-CROWN WHEEL	8		CHF 14.85

Ill.no.	Partno.	Part	Quantity required	Info	Price
17	6K875	LOCKTAB MGA CROWN WHEEL & PINION	4		CHF 6.00

Ill.no.	Partno.	Part	Quantity required	Info	Price
18	88G283	CROWNWHEEL & PINION 4.3:1	1	standard, (10/43)	CHF 801.90
18	88G284	10 SPLINT CROWN WHEEL & PINION 4.55:1	1	optional (9/41)	CHF 868.15
18	BTB653	CROWN WHEEL & PINION 3.9:1	1	optional (11/43)	CHF 801.90
18	267-166	CROWNWHEEL&PINION 3.7:1 MGA & B BANJO	1	optional (1/37)	CHF 801.90
18	ATB7240	CROWNWHEEL&PINION 4.1:1	1	MkII only, (10/41)	CHF 801.90

Ill.no.	Partno.	Part	Quantity required	Price
19	ATB7064	THRUST 0.126	a/r	CHF 63.25
19	ATB7065	THRUST 0.124	a/r	CHF 63.10
19	ATB7066	THRUST 0.122	a/r	CHF 61.95
19	ATB7067	THRUST 0.120	a/r	CHF 65.85
19	ATB7068	THRUST 0.118	a/r	CHF 60.50
19	ATB7069	THRUST 0.116	a/r	CHF 64.25
19	ATB7070	THRUST WASHER .114	a/r	CHF 52.05
19	ATB7071	THRUST 0.112	a/r	CHF 58.35

Ill.no.	Partno.	Part	Quantity required	Info	Price
20	100897A	PINION BEARING, INNER	1		CHF 60.00

Ill.no.	Partno.	Part	Quantity required	Info	Price
21	1B7240	SPACER DIFF BEARING	1		CHF 86.95

Ill.no.	Partno.	Part	Quantity required	Info	Price
22	2A7213	BEARING PINION OUTER	1		CHF 39.75

Ill.no.	Partno.	Part	Quantity required	Price
25	ATB7102	SHIM 0.004	a/r	CHF 4.00
25	ATB7103	SHIM 0.006	a/r	CHF 7.85
25	ATB7104	SHIM 0.008	a/r	CHF 3.60
25	ATB7105	SHIM 0.010	a/r	CHF 5.60
25	ATB7106	SHIM 0.012	a/r	CHF 4.30
25	ATB7107	SHIM 0.020	a/r	CHF 4.10
25	ATB7108	SHIM 0.030	a/r	CHF 4.35

Ill.no.	Partno.	Part	Quantity required	Info	Price
26	88G320	SEAL DIFF NOSE BANJO	1		CHF 7.05

Ill.no.	Partno.	Part	Quantity required	Info	Price
27	1G7349	USE 1G7439	1

Ill.no.	Partno.	Part	Quantity required	Info	Price
28	ATB7059	FLANGE FRONT CW & P	1		CHF 199.90

Ill.no.	Partno.	Part	Quantity required	Info	Price
29	WL600121	WASHER SPRING 3/4	1		CHF 1.95

Ill.no.	Partno.	Part	Quantity required	Info	Price
30	FNZ612	NUT 3/4 UNF HT THIN	1		CHF 9.35

Ill.no.	Partno.	Part	Quantity required	Info	Price
33	2K8160	CORE PLUG 1 5/16"	2		CHF 3.80

Ill.no.	Partno.	Part	Quantity required	Info	Price
34	ATB7206	HALF SHAFT WIRE WHL MGA 10 SPLINE (FOR ORIG WIRE	2	1500cc - 10 spline	CHF 216.20
34	ATB7386	1/2 SHAFT WW1600 26SP	2	1600cc to (c)82748 - 26 spline	availability request (add quantity to basket, offer follows)
34	BTB153	HALF SHAFT AXLE, WIRE WHEELS	2	1600cc from (c)82749 - 25 spline	CHF 180.80
34	ATB7206S	HALF SHAFT MGA 10 SPLINE WIRE WHEEL CONVERSION	2	1500cc - 10 spline	availability request (add quantity to basket, offer follows)
34	ATB7386S	SP 1/2 SHAFT 26 SPLINE	2	1600cc to (c)82748 - 26 spline	CHF 211.35
34	BTB153S	HALF SHAFT, AXLE, WIRE WHEEL, 25 SPLINE	2	1600cc from (c)82749 - 25 spline	CHF 209.90

Ill.no.	Partno.	Part	Quantity required	Info	Price
35	ATB7204	HUB WW REAR MGA RH	1		CHF 171.55
35	ATB7205	HUB WW REAR MGA LH	1		CHF 171.55

Ill.no.	Partno.	Part	Quantity required	Info	Price
36	RCK107R	HUB ADAPTOR, WIRE WHEEL, REAR, 12 TPI, RH	1		CHF 136.85
36	RCK107L	HUB ADAPTOR, WIRE WHEEL, REAR, 12 TPI, LH	1		CHF 136.85

Ill.no.	Partno.	Part	Quantity required	Info	Price
37	110366	NUT, FOR ADAPTORS	8		CHF 1.70

Ill.no.	Partno.	Part	Quantity required	Info	Price
38	ATB7190SR	STEEL WHEEL HALF SHAFT	2	1500cc	availability request (add quantity to basket, offer follows)
38	ATB7279	AXLE-STEEL WHEEL NCA	2	1600cc To (c)82892	availability request (add quantity to basket, offer follows)
38	BTB151	HALF SHAFT STEEL WHL MGA1600 LATE (NO LONGER AVAIL	2	1600cc From (c)82893	availability request (add quantity to basket, offer follows)

Ill.no.	Partno.	Part	Quantity required	Info	Price
39	ATB7352	HUB STEEL WHEEL	2		CHF 204.95
39	ATB7391	HUB WIRE WHEEL NCA	2		availability request (add quantity to basket, offer follows)

Ill.no.	Partno.	Part	Quantity required	Info	Price
40	1G7435	STUD, STEEL WHEEL	8		CHF 6.65
40	ATB7201	WHEEL STUD WW MGA RR	8		CHF 21.55

Ill.no.	Partno.	Part	Quantity required	Info	Price
41	88G276	WHEEL NUT MGA SW	8		CHF 6.25
41	FNZ507	NUT 7/16 UNF HT	8		CHF 3.60
NI	GHK1133	BEARING KIT-REAR A&B-BANJO	2	inc. items 40, 43, 44, 45	CHF 42.65

Ill.no.	Partno.	Part	Quantity required	Info	Price
42	GFG111	GASKET FLANGE	2		CHF 2.05

Ill.no.	Partno.	Part	Quantity required	Info	Price
43	ATB7354	O RING SEAL - BANJO	2		CHF 1.85

Ill.no.	Partno.	Part	Quantity required	Info	Price
44	GHS211	OIL SEAL MGA/B BANJO	2		CHF 7.25

Ill.no.	Partno.	Part	Quantity required	Info	Price
45	GHB127	BEARING REAR A&B BANJO	2		CHF 35.45

Ill.no.	Partno.	Part	Quantity required	Info	Price
46	1G7436	BEARING SPACER	2	steel wheel	CHF 57.90

Ill.no.	Partno.	Part	Quantity required	Info	Price
47	ATB7181	USE BTB1277	1

Ill.no.	Partno.	Part	Quantity required	Info	Price
48	ATB7283E	4.3:1 EARLY MGA DIFF	1	(4.3:1, 10 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	ATB7283EX	DIFF 4.3 BANJO NEW CROWN WHEEL & PINION	1	(4.3:1, 10 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1284E	DIFF 4.3:1 BANJ 25SP	1	(4.3:1, 25 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1284EX	DIFF 4.3 BANJO NEW CROWN WHEEL & PINION	1	(4.3:1, 25 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB217E	DIFF 4.3:1 BANJ 26SP	1	(4.3:1, 26 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB217EX	DIFF 4.3:1 BANJ 26SP	1	(4.3:1, 26 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1285E	DIFF 3.9:1 BANJ 25SP	1	(3.9:1, 25 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1285EX	DIFF 3.9 BANJO NEW CROWN WHEEL & PINION	1	(3.9:1, 25 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1285ELX	DIFF 3.9 BANJO NEW CROWN WHEEL & PINION & LSD	1	(3.9:1, 25 spline - Reconditioned with new CW&P & LSD)	availability request (add quantity to basket, offer follows)
48	BTB216E	DIFF 4.55:1 BANJ 26SP	1	(4.55:1, 25 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB216EX	DIFF 4.55:1 BANJ 26SP	1	(4.55:1, 25 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB216EXL	DIFF 4.55:1 BANJ 26SP +LSD	1	(4.55:1, 25 spline - Reconditioned with new CW&P & LSD)	availability request (add quantity to basket, offer follows)

Ill.no.	Partno.	Part	Quantity required	Info	Price
50	ARB101	PIN CHECK STRAP AXLE	2	weld to axle	CHF 34.90

Ill.no.	Partno.	Part	Quantity required	Info	Price
51	PWZ206	WASHER, PLAIN, 3/8" ID X 1.1/4" OD	2		CHF 2.00

Ill.no.	Partno.	Part	Quantity required	Info	Price
52	GHF333	WASHER SPRING 3/8	2		CHF 0.35

Ill.no.	Partno.	Part	Quantity required	Info	Price
53	GHF202	NUT PLAIN 3/8 UNF	2		CHF 0.60

Ill.no.	Partno.	Part	Quantity required	Info	Price
1	1G7582	HUB LOCKING NUT LH THREAD	1		CHF 41.35
1	1G7448	LOCKING NUT RH	1/2		CHF 41.35
2	1G7584	WASHER, LOCKING	2		CHF 6.90
3	6K499	DRAIN PLUG	2		CHF 4.95
4	21H6060	VALVE, BREATHER REAR AXLE CASING	1		CHF 14.00
5	1G7465	GASKET, DIFFERENTIAL	1		CHF 2.05
6	BTB328	DIFF CAGE BANJO AXLE	1		availability request (add quantity to basket, offer follows)
8	CHM163	BEARING DIFFERENTIAL CARRIER	2		CHF 41.80
9	2K7993	SHIM BEARING PACKING 0.002"	a/r		CHF 5.75
9	ATB7239	SHIM B/AXLE .003	a/r		CHF 5.00
9	2K7435	SHIM BEARING PACKING, 0.004"	a/r		CHF 5.90
9	6K503	SHIM B/AXLE .006	a/r		CHF 6.10
10	ATB7122	DIFF GEAR MGA1500	2	1500cc	CHF 192.85
10	ATB7282	DIF GEAR NCA	2	1600cc To (c)82892 s/wheel To (c)82748 wire wheel	availability request (add quantity to basket, offer follows)
10	BTB150	DIFFERENTIAL WHEEL 25 SPLINE	2	1600cc From (c)82893 s/wheel From (c)82749 wire wheel	CHF 182.30
11	ATB7072	THRUST 35THOU STD	2		CHF 8.45
12	ATB7123	PLANET GEAR MGB	2		CHF 135.80
13	1G7445	THRUST WASHER, PINION	2		CHF 10.10
14	1G7444	SHAFT, PINION GEAR	1		CHF 62.55
15	6K842	DIFF PEG NCA	1		availability request (add quantity to basket, offer follows)
16	ATA7043	BOLT-CROWN WHEEL	8		CHF 14.85
17	6K875	LOCKTAB MGA CROWN WHEEL & PINION	4		CHF 6.00
18	88G283	CROWNWHEEL & PINION 4.3:1	1	standard, (10/43)	CHF 801.90
18	88G284	10 SPLINT CROWN WHEEL & PINION 4.55:1	1	optional (9/41)	CHF 868.15
18	BTB653	CROWN WHEEL & PINION 3.9:1	1	optional (11/43)	CHF 801.90
18	267-166	CROWNWHEEL&PINION 3.7:1 MGA & B BANJO	1	optional (1/37)	CHF 801.90
18	ATB7240	CROWNWHEEL&PINION 4.1:1	1	MkII only, (10/41)	CHF 801.90
19	ATB7064	THRUST 0.126	a/r		CHF 63.25
19	ATB7065	THRUST 0.124	a/r		CHF 63.10
19	ATB7066	THRUST 0.122	a/r		CHF 61.95
19	ATB7067	THRUST 0.120	a/r		CHF 65.85
19	ATB7068	THRUST 0.118	a/r		CHF 60.50
19	ATB7069	THRUST 0.116	a/r		CHF 64.25
19	ATB7070	THRUST WASHER .114	a/r		CHF 52.05
19	ATB7071	THRUST 0.112	a/r		CHF 58.35
20	100897A	PINION BEARING, INNER	1		CHF 60.00
21	1B7240	SPACER DIFF BEARING	1		CHF 86.95
22	2A7213	BEARING PINION OUTER	1		CHF 39.75
25	ATB7102	SHIM 0.004	a/r		CHF 4.00
25	ATB7103	SHIM 0.006	a/r		CHF 7.85
25	ATB7104	SHIM 0.008	a/r		CHF 3.60
25	ATB7105	SHIM 0.010	a/r		CHF 5.60
25	ATB7106	SHIM 0.012	a/r		CHF 4.30
25	ATB7107	SHIM 0.020	a/r		CHF 4.10
25	ATB7108	SHIM 0.030	a/r		CHF 4.35
26	88G320	SEAL DIFF NOSE BANJO	1		CHF 7.05
27	1G7349	USE 1G7439	1
28	ATB7059	FLANGE FRONT CW & P	1		CHF 199.90
29	WL600121	WASHER SPRING 3/4	1		CHF 1.95
30	FNZ612	NUT 3/4 UNF HT THIN	1		CHF 9.35
33	2K8160	CORE PLUG 1 5/16"	2		CHF 3.80
34	ATB7206	HALF SHAFT WIRE WHL MGA 10 SPLINE (FOR ORIG WIRE	2	1500cc - 10 spline	CHF 216.20
34	ATB7386	1/2 SHAFT WW1600 26SP	2	1600cc to (c)82748 - 26 spline	availability request (add quantity to basket, offer follows)
34	BTB153	HALF SHAFT AXLE, WIRE WHEELS	2	1600cc from (c)82749 - 25 spline	CHF 180.80
34	ATB7206S	HALF SHAFT MGA 10 SPLINE WIRE WHEEL CONVERSION	2	1500cc - 10 spline	availability request (add quantity to basket, offer follows)
34	ATB7386S	SP 1/2 SHAFT 26 SPLINE	2	1600cc to (c)82748 - 26 spline	CHF 211.35
34	BTB153S	HALF SHAFT, AXLE, WIRE WHEEL, 25 SPLINE	2	1600cc from (c)82749 - 25 spline	CHF 209.90
35	ATB7204	HUB WW REAR MGA RH	1		CHF 171.55
35	ATB7205	HUB WW REAR MGA LH	1		CHF 171.55
36	RCK107R	HUB ADAPTOR, WIRE WHEEL, REAR, 12 TPI, RH	1		CHF 136.85
36	RCK107L	HUB ADAPTOR, WIRE WHEEL, REAR, 12 TPI, LH	1		CHF 136.85
37	110366	NUT, FOR ADAPTORS	8		CHF 1.70
38	ATB7190SR	STEEL WHEEL HALF SHAFT	2	1500cc	availability request (add quantity to basket, offer follows)
38	ATB7279	AXLE-STEEL WHEEL NCA	2	1600cc To (c)82892	availability request (add quantity to basket, offer follows)
38	BTB151	HALF SHAFT STEEL WHL MGA1600 LATE (NO LONGER AVAIL	2	1600cc From (c)82893	availability request (add quantity to basket, offer follows)
39	ATB7352	HUB STEEL WHEEL	2		CHF 204.95
39	ATB7391	HUB WIRE WHEEL NCA	2		availability request (add quantity to basket, offer follows)
40	1G7435	STUD, STEEL WHEEL	8		CHF 6.65
40	ATB7201	WHEEL STUD WW MGA RR	8		CHF 21.55
41	88G276	WHEEL NUT MGA SW	8		CHF 6.25
41	FNZ507	NUT 7/16 UNF HT	8		CHF 3.60
NI	GHK1133	BEARING KIT-REAR A&B-BANJO	2	inc. items 40, 43, 44, 45	CHF 42.65
42	GFG111	GASKET FLANGE	2		CHF 2.05
43	ATB7354	O RING SEAL - BANJO	2		CHF 1.85
44	GHS211	OIL SEAL MGA/B BANJO	2		CHF 7.25
45	GHB127	BEARING REAR A&B BANJO	2		CHF 35.45
46	1G7436	BEARING SPACER	2	steel wheel	CHF 57.90
47	ATB7181	USE BTB1277	1
48	ATB7283E	4.3:1 EARLY MGA DIFF	1	(4.3:1, 10 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	ATB7283EX	DIFF 4.3 BANJO NEW CROWN WHEEL & PINION	1	(4.3:1, 10 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1284E	DIFF 4.3:1 BANJ 25SP	1	(4.3:1, 25 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1284EX	DIFF 4.3 BANJO NEW CROWN WHEEL & PINION	1	(4.3:1, 25 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB217E	DIFF 4.3:1 BANJ 26SP	1	(4.3:1, 26 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB217EX	DIFF 4.3:1 BANJ 26SP	1	(4.3:1, 26 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1285E	DIFF 3.9:1 BANJ 25SP	1	(3.9:1, 25 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1285EX	DIFF 3.9 BANJO NEW CROWN WHEEL & PINION	1	(3.9:1, 25 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB1285ELX	DIFF 3.9 BANJO NEW CROWN WHEEL & PINION & LSD	1	(3.9:1, 25 spline - Reconditioned with new CW&P & LSD)	availability request (add quantity to basket, offer follows)
48	BTB216E	DIFF 4.55:1 BANJ 26SP	1	(4.55:1, 25 spline - Reconditioned with existing CW&P)	availability request (add quantity to basket, offer follows)
48	BTB216EX	DIFF 4.55:1 BANJ 26SP	1	(4.55:1, 25 spline - Reconditioned with new CW&P)	availability request (add quantity to basket, offer follows)
48	BTB216EXL	DIFF 4.55:1 BANJ 26SP +LSD	1	(4.55:1, 25 spline - Reconditioned with new CW&P & LSD)	availability request (add quantity to basket, offer follows)
50	ARB101	PIN CHECK STRAP AXLE	2	weld to axle	CHF 34.90
51	PWZ206	WASHER, PLAIN, 3/8" ID X 1.1/4" OD	2		CHF 2.00
52	GHF333	WASHER SPRING 3/8	2		CHF 0.35
53	GHF202	NUT PLAIN 3/8 UNF	2		CHF 0.60